A1 Garage Door Service is known for providing only the best value for money. We always aim for the best possible customer service and experience, reasonable costs for our products and services, give FREE estimates and FREE professional advice as well as amazing deals and discounts when you book our service. What’s more, we GUARANTEE that we service all manufacturer warranties, including lifetime warranties. What more can you ask for?
The technician, Robert Helton, was very pleasant, helpful, and professional. He repaired the garage door opener expeditiously and explained why it hadn't worked properly. He also checked the chain mechanism and the door itself and showed me how to manually work the door should I need to do that in the future. I was very pleased with this repair work.
Replacing a circuit board sounds like a scary garage door repair, but it’s really quite easy. It will take 10 minutes tops and only requires a 1/4-in. nut driver. Just follow these steps: Remove the light cover, take out the lightbulb, disconnect the switch and safety sensor wires, remove a few screws, unplug the board and you’re done. A circuit board will cost about $80, so make sure you protect your new one with a surge protector. You can buy an individual outlet surge protector at a home center for less than $10.
A garage door opener is a motorized device that is used to open and close a garage door. Garage door openers are controlled using remotes, keypads, or even smartphones. Having a garage door opener is just as important as the door itself. The ability to open your door without having to physically step out of your car is an excellent convenience in today's society.
We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?

"I couldn't be happier, they solved a year long problem we had that a competing company of theirs (who installed the garage on our new home) couldn't fix! I feel Ric and Randy both (who have fixed a garage at my old house and my new house) take a lot of pride in their work, they are ethical and operate with integrity. I only want to work with Precision Garage Door from now on. I'd recommend them to anyone and everyone! ”


Fiberglass and vinyl garage doors are composite units, combining a steel core behind a fiberglass or vinyl skin. They have also polyurethane insulated base sections, or other type of foam insulation. These premium doors can match steel garage doors, and be a realistic imitation of wood (namely fiberglass units), but they may be more expensive than steel units.

I had an unusual problem with my door opener that totally stumped 2 previous companies. They would sell me parts that did not fix the problem. Then I tried A1 Door Garage Service. A1 was also initially stumped, but kept exploring solutions. Even refunding my cost of parts I bought that did not resolve the issue. How's THAT for great service. After about 5 visits from A1 the problem is fixed. I am very pleased. JD from A1 stuck with it and did not give up until I was satisfied with the repair, and adjusted my final bill to reflect a refund of parts I purchased that did not fix the problem.
Sears offers two different drive mechanisms to accommodate your home and budget. If you're looking for a smooth and quiet opener for a garage door with rooms located above the garage or attached to the garage, the belt drive is going to be the best for you. You can also choose a chain drive opener, which is perfect for garages that are unattached to the home.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
One way to control the opening and closing of your garage door is by using a remote. The remotes are often handy keychain-sized controls, perfect for storing in your purse or right in your car. The remote controls are programmed using “rolling” codes. This makes it harder for thieves or burglars to get access to your security code and break in. The garage door will only function using the appropriate transmitters with assigned codes. Remote controls are included in the package when purchasing a garage door opener. If they are misplaced or broken, the cost of purchasing a replacement remote control for your garage door averages between $25 and $50.
what should be the length of the drain vent. I had it at the roof level. But since I am getting bad smell in my house via bathrooms (or may be via roof door), I have just extended the length of the vent pipe. Is there any scientific method to estimate the right length? Plus is there any tester to test from where the bad sewage odor is coming from into the living room. It's a two-story villa.

I had Russ out to my house on July 16th for a simple motor replacement. While he was inspecting my door, he found several significant cracks. He took the time to point them out to my husband and advised that we really need a new door along with the motor. The following day Craig came out to do an estimate. He was so polite and professional, very no nonsense, and didn't try to sell us anything we don't need. He came back again on the 19th and took measurements, we signed a contract, and are scheduled to get our new door and motor on the 25th. We have had issues with our door not opening or closing all the way for the last 4 years during the summer heat. It will be so nice to have peace of mind that our garage door and the motor will last a very long time. I truly appreciate the honesty and integrity of your technicians! Thank you!
Align the upper roller tracks by carefully lifting the door halfway. Lock it in place with two locking pliers, and install the supporting brackets on the back of the rails using 1-1/4 in. perforated angle iron (available at home centers and hardware stores). Install 1-1/2 x 1/4 in. stop bolts, with the threads to the inside of the track, at the end of each upper track.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.

I was very happy with Precision Garage Door! They had Nick come out to my house the very day I called for help He was thorough in examining and explaining the condition of all of the parts of the garage door setup, problems I had, options, pricing. A spring had broken on our door just the day before, and Nick replaced the set of springs plus installed new "drones" (I believe, aka "wheels") and bearings, which were very old and wearing on the unit. I am absolutely satisfied thus far and would highly recommend Precision Garage Door. Also, Nick was professional, friendly, helpful, thorough, and easy to talk to. Thank you very much for your quick help in this situation!!!
All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
Insulation, which increases energy efficiency and can help to lower utility bills, is crucial when a garage door is attached to the home. In this case, doors with high R-values are preferred. This means it has insulation that can keep the heat in. The higher the R-value, the better insulated your garage will be against outside noise and cold and hot air.
I chose Precision because of an ad I saw advertising free service call. I was looking to replace the sensors on 2 garage doors. Ben the tech- very nice and knowledgeable told me I would have to replace both units because the base unit was too old. Fine not what I was looking to do but I understood until he quoted me over $900 for 2 units. My friend just had hers replaced for $350. When I told Ben I would think about it He said that would be $80 for the service call. My free coupon only works if you get a repair. It took less than 15 mins. Needless to say I have called a few other companies and the going rate is $340-$350 no service fee
The manager is very thorough in providing all the options with detail so that i can make a sound decision. He recommended the option he believe is the best but never pressure me into signing up for that. Just one small negative - Time management. I was booked on a 12-2pm window because of my meeting but got a call at 10:50am that the rep is on the way. I have to rush out of the meeting and drive home.
In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the project yourself, but you should recruit help for removing the old door.
R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.
Wonder how much Festool is paying Silva to showcase their outrageously expensive line of tools. He used practically the entire product line on this project that was nothing more than a Festool commercial. I guess the brad nailer company didn't offer any kickbacks to the crew because you never saw their brand name. This show has turned into nothing more than crass commercialism. And when did Silva become a 'master carpenter'. He can't hold a candle to Abrams. Never could. But he's definitely better at milking the sponsors. Would love to see the inside of his workshop.
Lower the door and dismantle it by removing the hardware. Lower a double door by recruiting at least two helpers to help with the weight, and place a 2×4 block under the door to prevent smashing a foot or finger when it’s lowered. Remove the sections one at a time by disconnecting the rollers and brackets. If you have windows, tape them to help control flying shards if they break. Then remove the old roller tracks and remaining hardware.
Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.
Thank you, thank you, thank you for sharing your knowledge. I just replaced our shower cartridge and our leak is FIXED!!!!!!! Your instructional was clear and concise. I did purchase 2 cartridges first, because I did not know the type it was and could not pull it out without the plastic cover it comes with. Fortunately, it was one of the two. By the way I'm a 63 year old woman. If I can do it, anyone with internet and a little patience and an hour can do it.....
I had an unusual problem with my door opener that totally stumped 2 previous companies. They would sell me parts that did not fix the problem. Then I tried A1 Door Garage Service. A1 was also initially stumped, but kept exploring solutions. Even refunding my cost of parts I bought that did not resolve the issue. How's THAT for great service. After about 5 visits from A1 the problem is fixed. I am very pleased. JD from A1 stuck with it and did not give up until I was satisfied with the repair, and adjusted my final bill to reflect a refund of parts I purchased that did not fix the problem.
The electronics should also be inspected before or after investing in the cost of replacing the garage door panel to make sure your door will operate properly. The sensors prevent the door from closing on someone's foot or a pet. If they don't work, someone could be injured. Also check to make sure the door opener works, since you could otherwise be locked out of your garage.

I have recently purchased a house with an older roof that needs to be restored soon. So, I am trying to decide on I should go with a metal roof other than shingles. If I install metal roofing over solid decking such as OSB or plywood, integrate with a properly insulated garret, there is very little noise difference compared to standard asphalt shingles. I have briefly read benefits and drawbacks of Metal roofing but as I listed before I should go to metal roofing and hiring a roofing contractor no matter its expensive or noisy anyhow, Your article has cleared a lot of misinterpretation I’ve had before.
Our garage door installation and repair professionals are courteous, knowledgeable, skilled and dedicated to your satisfaction. Let us show you what we’ve done for so many businesses and homes throughout Cincinnati and northern Kentucky when it comes to their garage doors, and what we can do for you. Once you’ve tried our services, you won’t have to search for a garage door service provider in this area ever again.
Measure the various areas where the door will be installed: door-opening height and width, headroom (from top of opening to ceiling), and back room (length of garage). For the headroom, you should have about 10" to 12" of space, depending on the spring system you're installing. For the back room, you should have the door height, plus another 18" or more of space.

We only hire and train very experienced technicians, so you can be confident that you will get the best garage door service available. We strive for 100% customer satisfaction on all our work and stand behind our garage door service if you have any issue whatsoever. Our reviews tell of our dedication to excellence and offering the ABSOLUTE best quality products and customer experience. You can check out what our customers have to say about their experience to the Better Business Bureau by clicking here! We guarantee to be the overall top choice in the market for all your garage door needs. We are a family owned garage door company from the Central Kentucky area and only hire technicians that put forth the same honest values that we have. We strive for 100% customer satisfaction and if for any reason that you are unhappy with a technician or their service, we will be happy to make the experience right as we pride ourselves and our company on the highest of customer satisfaction and experience while offering the lowest prices in the market. We are top rated with all service rating and reviewing companies such as BBB, Home Advisor, Demandforce, and Angie’s List. We take our customers experince serious and we guarantee it!
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
A1 Garage Door Service is the trusted service provider in installing, servicing and repairing all kinds and types of garage doors. We encourage you to check out the reviews of the people of Phoenix and Chandler on the kind of garage door service that we provide. Our customers have consistently given us A+ ratings on BBB, 5-star ratings on Yelp and the Super Service Award on Angie’s List to express their satisfaction on our service.
Give your garage the strength and style it Give your garage the strength and style it needs with a Clopay Garage Door. The 1-layer raised panel steel construction provides durability and style. Added strength is provided by the outer steel skins. The price includes the door and components only. Installation is NOT included.  More + Product Details Close
To make sure the job gets done right, our professional installers are local, licensed and insured. With a 9.7 out of 10 VOC score, our garage installers will exceed your expectations, provide reliable service, and install attractive garage doors that will transform your home’s appearance. All labor, products and installations are 100% backed by The Home Depot. Service you can trust.

Extension spring systems should always be restrained by a safety cable that runs through the middle of the spring, tying off to a solid point at the rear and front of the horizontal door track. Extension springs represent a hazard to bystanders when a spring, pulley, or cable breaks under tension. Metal parts from extension spring systems can suddenly be launched.
×