Beware these aluminum clad wood doors. The wood is particle board. Why would anyone make a storm door out of particle board? They don't seal it in any way, it gets wet between the aluminum cladding and boils and blisters the aluminum and looks terrible in just a few years. I have two Larson's and they were horrible doors almost from the start. I've seen reviews and EMCO is the exact same way. When your storm door needs a storm door, you bought the wrong door.
Not sure what’s wrong with your garage door? Don’t know how much it will cost to repair? With Precision Garage Door Service of Omaha, you’ll never have to worry about an unexpected bill. Contact one of our professionals today for a free technical evaluation and repair estimate. Once we’ve given you a price, you’ll be able to confidently make the decision whether you’ll want to move forward with the repair.

A torsion spring counterbalance system consists of one or two tightly wound up springs on a steel shaft with cable drums at both ends. The entire apparatus mounts on the header wall above the garage door and has three supports: a center bearing plate with a steel or nylon bearing and two end bearing plates at both ends. The springs themselves consist of the steel wire with a stationary cone at one end and a winding cone at the other end. The stationary cone is attached to the center bearing plate. The winding cone consists of holes every 90 degrees for winding the springs and two set screws to secure the springs to the shaft. Steel counterbalance cables run from the roller brackets at the bottom corners of the door to a notch in the cable drums. When the door is raised, the springs unwind and the stored tension lifts the door by turning the shaft, thus turning the cable drums, wrapping the cables around the grooves on the cable drums. When the door is lowered, the cables unwrap from the drums and the springs are rewound to full tension.[7]


Vincent was professional, informative, personable, efficient, and cleaned up his work area as he worked. I told him and now I am telling you... He my "Jordan" of garages. Give him a raise or at least a bonus. Thank you for sending him for my install. I am extremely pleased with my garage opener & with his install and information I am confident in its operation. Thank you.
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
Absolute Overhead Door recently launched a blog that can be found here so that readers would be able to see the benefits of a garage and what they should do in the event their newly driving teenage drove into the garage door. The blog offers many tips for “fix at home” solutions as well as giving examples of situations when calling us for a service call is the best decision. In our blog, we give professional and honest recommendations for the most reader and budget friendly options for families looking for advice that doesnt cost a fortune and an obligation to purchase a new garage door from a salesman afterwards! Check it out! We hope you enjoy it.
Get a price quote on a New Garage Door- Use our super-simple garage door designer to learn about the available options, pick the ones you like best, and send it to us for a free quote. It's the fastest way to shop for a garage door on the web. In less than 10 minutes, you'll have a much better idea what you want and get a price without sales pressure. Click garage door designer to get started...
Another way to control the opening and closing of your garage door is using a keypad. This is a great way to get into the garage without having to worry about having your key or remote control. Key pads are often installed on the outside of the garage door on the wall. Keypads are controlled using a PIN number that you enter using the touchpad. You can do this to open and close the garage. You can even create temporary PINs for giving access to your repair workers, delivery men, or even neighbors, for a keyless entry. Keypads can be purchased separately from a garage door opener. Keypads for garage doors average in price between $25-$70.
Our branch in the city of Tucson services the garage door needs of Old Pueblo including Oro Valleyand Marana in the northwest, Sahuarita and South Tucson in the south, and; the communities of Casas Adobes, Catalina Foothills, Flowing Wells, Midvale Park, Tanque Verde, Tortolita and Vail. We also cater to surrounding areas such as Catalina and Oracle in the north, Green Valley in the south and Benson on the southeast. When you call us, expect our technicians to arrive promptly and efficiently attend to your garage door needs.

When you install a new garage door, replace all the hardware as well. If your automatic opener doesn’t have an automatic reversing system that includes photoelectric eyes, replace it. Doors with openers also require two extra pieces of hardware that you’ll see in Photo 4: a support strut (usually included in the door kit) and an opener bracket (not included). For doors with torsion springs located over the door, spend the $50 or so to have a garage door professional release the tension.
A common material for a new garage door is steel sheet formed or stamped to look like a raised panel wooden door. Steel doors are available in uninsulated, insulated, and double skin steel. A design mimicking carriage house doors has become popular since early 2000s, and many manufacturers clad the exterior of a steel door with composite, vinyl boards, or other trim to give it the appearance of wood.
One way to control the opening and closing of your garage door is by using a remote. The remotes are often handy keychain-sized controls, perfect for storing in your purse or right in your car. The remote controls are programmed using “rolling” codes. This makes it harder for thieves or burglars to get access to your security code and break in. The garage door will only function using the appropriate transmitters with assigned codes. Remote controls are included in the package when purchasing a garage door opener. If they are misplaced or broken, the cost of purchasing a replacement remote control for your garage door averages between $25 and $50.
When it comes to garage doors, Jarusewski’s Overhead Door Service Inc. is your premiere choice. We are true professionals and your satisfaction is key. Let us show you the quality of our garage doors and how you can improve both the look and value of your home or business. From the appearance of the door, right down to strength and durability, we’ve got a door for everyone.
I am writing this review on 9/6/2018. We spent over $1000.00 on our garage door to have basically all new parts but that is not the reason for this review. After all of the work the door still closed rather hard, I called on Sunday 9/2/2018 and asked if someone could come by and check to see if it can be adjusted so it does not close so hard. I asked if there would be a charge and was told no. Today a tech named Adam came and my wife told me he was the most rude arrogant and condescending individual that has ever come to our home, My wife was so upset they way he talked down to her. You may want to call so she can give you the whole story. Our phone num
When you pull up to your garage door and push the button for the opener, there’s one thing that should happen: your garage door should open smoothly, steadily, and quietly. However, if that’s not happening, contact the friendly professionals at Garage Door Service. We’re located in Loveland, Colorado, but we’re also prepared to offer service, garage door repair, and garage door opener repair to customers in Fort Collins, Windsor, and all over Northern Colorado, as well as Wyoming, Nebraska, and Kansas. No matter the problem, our technicians always come prepared with a wide range of parts and tools, so that we can repair your garage door during a single visit. We’re committed to providing reasonable rates, free estimates, and top-notch customer service. Our goal is to leave you with a working garage door and a smile.
Installing a garage door opener requires knowledge so that it can be installed properly. Hiring a professional electrician to do the job is a good idea. Installing a garage door opener includes the following: preparation of all the main parts (the rails 2, trolley, motor component), attaching the blocking and bracket 3, installation of additional features (safety rope, light bulb, keypad, safety sensors 1), and testing to ensure that the door runs smoothly and the remotes are functioning properly.
The technician, Robert Helton, was very pleasant, helpful, and professional. He repaired the garage door opener expeditiously and explained why it hadn't worked properly. He also checked the chain mechanism and the door itself and showed me how to manually work the door should I need to do that in the future. I was very pleased with this repair work.
I am writing this review on 9/6/2018. We spent over $1000.00 on our garage door to have basically all new parts but that is not the reason for this review. After all of the work the door still closed rather hard, I called on Sunday 9/2/2018 and asked if someone could come by and check to see if it can be adjusted so it does not close so hard. I asked if there would be a charge and was told no. Today a tech named Adam came and my wife told me he was the most rude arrogant and condescending individual that has ever come to our home, My wife was so upset they way he talked down to her. You may want to call so she can give you the whole story. Our phone num
If you are replacing an old garage door, the first step is to measure your garage opening to ensure you are choosing a door with the correct dimensions. Even if you feel confident that your door is a standard size, measuring first can help ensure that buying your door is an enjoyable and smooth process. View our installation guide to get the needed measurements for your door. If you find that you have an odd-sized garage door, use our QuickDraw tool to see how a specific model will look in your desired size. If you have a unique vision for your home's curb appeal, Clopay can also design custom garage doors to meet your specifications.
Squealing, screeching, or grinding noises from your garage door are usually indicative of a lack of lubricant or an accumulation of dirt or debris in the tracks. When removing debris, do not use harsh chemicals to clean the tracks. Once the track is clean, coat it with lubricant designed especially for garage doors, if possible. If you do not have access to this special type of lubricant, you can use WD-40 on the tracks and hardware.
We are a family owned company with over 20 years of professional experience in garage door repair. We are constantly working to keep our intensive training up-to-date so that our uniformed technicians are ready to assist you with any garage door concerns, and so that you can always expect the finest quality of service to meet your needs and your budget. For the best technicians and the best repairs for your home garage door, look no further. Contact us today for great results at a fraction of the cost.

Thank you! Every time we walk into the garage we are thrilled because we have daylight. The doors are so quiet, we giggle that no one has been awakened by the racket that used to announce the doors being opened or closed. And the option of having an outside keyless entry is great too, It's just a wonderful feeling to know that you've fixed something and it was really worth it. Thanks again.


Both springs broke on my double door, and I had no idea who to call. I asked my smart phone for garage door repairs and they gave me one company listed in Lebanon. I called and set up an appointment with the tech and he said he would be there in an hour. After 4 hours I called and they got me to the tech and here is what he said after my 4 hour wait: "We can't do that, you will need to call someone else." I asked if he needed to reschedule, and he said, "No, call some other company." My temperature was high and I looked on my computer and Precision came up on the screen. I looked it over real good, checked the reviews and called them on Saturday morning. They said a tech could be out by noon. The tech called at 10:30 and said he could be here by 11am if that was alright. It was. John showed up at 11, we greeted each other, I felt good as soon as I met him. He looked over the door, sure enough both springs broke, cable off. He gave me 3 options: just fix the springs and cable; do that and change out the rollers which were clearly rusted and lots of play; and do that with a life-time warranty. No pressure, he was ready to do whatever I said. I told him the first option for now, and he went right to work. My wife and I discussed that our door was over 14 years old and has had no maintenance at all, and we decided to have the warranty. No problem. John was through and thorough in no time at all. The door sounded amazing, we had gotten so used to the noise, until it was not there any more - smooth and quiet and efficient. I am so thankful the other company blew me off, so that I came in contact with Precision. Great job. I will recommend them to everyone. 5 STARS ALL THE WAY!
Garage door sensors 1 are safety devices that prevent the garage door from closing on people, cars, pets, or anything that may get in its way. Garage door sensors 1 are located at the side of the door opening and produce a beam of infrared light. If the beam that runs from one side to the other is interrupted, the door will automatically reverse before hitting the object. Garage door sensors 1 can be purchased separately and average in price from $50-$100.
Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.
When I called to schedule the repair service, I was transferrd 5 times and spoke with 6 service reps. Each rep was very confused by my request to get my garage door repaired. One rep actually told me that Sears doesn't repair garage doors. I had to tell her that Sears installed the door. When I finally found a rep who could schedule my service, it took one week for the appointment.
"We had an unusual repair requirement. We have horizontal sliding steel doors on our 1950's equipment shed. The upper track was damaged by a roofer's forklift while they were loading supplies onto the roof. The track is made out of very heavy steel, not like the track in today's doors. Toby, responded to my request very quickly and came out of his way to inspect the damage. Although it was not something that he had encountered before, he was able to fix the track and the door is operating better than it has in years. Thank you."
"I couldn't be happier, they solved a year long problem we had that a competing company of theirs (who installed the garage on our new home) couldn't fix! I feel Ric and Randy both (who have fixed a garage at my old house and my new house) take a lot of pride in their work, they are ethical and operate with integrity. I only want to work with Precision Garage Door from now on. I'd recommend them to anyone and everyone! ”
Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
Technician gave me a window of 1-4pm, I called at 330 to see if he was on his way. He told me he would be there at 4pm, reason being was because of the amount of work orders he had that day. He was also by himself, had no helper. I was very satisfied that he was able to repair my garage door. He was very professional considering he showed up on a Friday afternoon on a 100 degree day. Thanks again
Lower the door and dismantle it by removing the hardware. Lower a double door by recruiting at least two helpers to help with the weight, and place a 2×4 block under the door to prevent smashing a foot or finger when it’s lowered. Remove the sections one at a time by disconnecting the rollers and brackets. If you have windows, tape them to help control flying shards if they break. Then remove the old roller tracks and remaining hardware.

Safe automatic door openers. All automatic openers must now have an auto-reversing mechanism and photoelectric eyes located near the floor on both sides of the door (see photo). If the door is closing and the beam between the eyes is interrupted, the door will automatically reverse. If the eyes aren’t connected, the door won’t operate. For instructions on how to install a new garage door opener, see How to Install a Garage Door Opener.
Given the complexity of a garage door and opener system, there are a variety of different areas something could go wrong. If your garage door shakes or is very loud during operation, the garage door closes all the way only to immediately open back up, the garage door opens slowly or closes too quickly, or the garage door opener and remote aren't working at all, you should seek help from a professional garage door repair specialist.
When your garage door starts acting up, more often than not it is telling you it's time to do a bit of maintenance. So, before hitting the panic button, try these simple repairs. First, examine the rollers and tracks. If you can't remember the last time you cleaned them (and they look the part!), give them a good brushing and then add some lubricant. Next, perform these simple garage door maintenance tasks.
When you pull up to your garage door and push the button for the opener, there’s one thing that should happen: your garage door should open smoothly, steadily, and quietly. However, if that’s not happening, contact the friendly professionals at Garage Door Service. We’re located in Loveland, Colorado, but we’re also prepared to offer service, garage door repair, and garage door opener repair to customers in Fort Collins, Windsor, and all over Northern Colorado, as well as Wyoming, Nebraska, and Kansas. No matter the problem, our technicians always come prepared with a wide range of parts and tools, so that we can repair your garage door during a single visit. We’re committed to providing reasonable rates, free estimates, and top-notch customer service. Our goal is to leave you with a working garage door and a smile.
Replacing a circuit board sounds like a scary garage door repair, but it’s really quite easy. It will take 10 minutes tops and only requires a 1/4-in. nut driver. Just follow these steps: Remove the light cover, take out the lightbulb, disconnect the switch and safety sensor wires, remove a few screws, unplug the board and you’re done. A circuit board will cost about $80, so make sure you protect your new one with a surge protector. You can buy an individual outlet surge protector at a home center for less than $10.
10The type of garage door shown provides the necessary lift assistance with a “torque tube.” If you intend to use an opener, wait to install the tube. Otherwise, install the torque tube according to the manufacturer’s directions. Roll up the door about 4 feet to check for the alignment of the tracks, and make any adjustments. Then tighten all fasteners.
Looking to repair your garage door opener? Common problems could range from issues with the remote or wall switch that control the garage door opener to more serious issues like a grinding noise coming from the opener itself. If you need help with repairing your garage opener, schedule a repair appointment today! We repair all major brands and have same-day availability in most markets, so we can get your garage door opener repaired and running smoothly. To learn more about the cost of repairing garage doors, visit our garage door and opener installation and repair cost guide.

If your garage door's spring breaks, stops working properly, or snaps, you'll lose the ability to open and close your garage door. This could happen due to a variety of issues, like normal wear and tear or from extreme temperature changes in a short amount of time. Spring replacements require a quick response from a garage door provider near you. Contact The Home Depot and a local, background-checked technician will respond within 24 hours.

Not interested in paying for maintenance on an outdated and failing system? Our installation services mean that you can have a brand new, high quality garage door installed in place of your existing model. Because we carry such a diverse range of products from the most industry-respected manufacturers, we’re sure to have a model that fits your needs and budget.
×