We are a family owned and operated company with local offices in various cities. We have offices in Arizona — from Phoenix to Tucson; Nevada— covering the entire Las Vegas metropolitan area, from North Las Vegas to Henderson; the Sunflower State of Kansas, from Wichita to Junction City; Wisconsin — spanning the entire Milwaukee county, from Fox Point to South Milwaukee; and Michigan, with our base in Sterling Heights.
Single panel doors can also be installed with (one piece track type hardware) that folds the door back with a single horizontal track on each side (which is mounted at the top of the wood frame) and a roller, (mounted to the top of the door on each side. A hinge on each side that attaches to the bottom of each side of garage door. Using track hardware, a car can be parked much closer to the door, as the whole door, when in the open position, rests completely inside of the garage door header. Track type hardware has much less arc when raising and lowering the garage door as opposed jamb type hardware.[citation needed]

The history of the garage door could date back to 450 BC when chariots were stored in gatehouses, but in the U.S. it arose around the start of the 20th century. As early as 1902, American manufacturers—including Cornell Iron Works—published catalogs featuring a "float over door." Evidence of an upward-lifting garage door can be found in a catalog in 1906.[4]

Almost all garage door openers come with a warranty. The warranty of your garage door opener will differ depending on where you purchased the product. The owner’s manual should give you the specific warranty information. Service is not covered by the warranty. If the owner chooses to have a professional service the opener or if the installation is a DIY, the warranty will not cover any repairs.
A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.
Extension spring systems should always be restrained by a safety cable that runs through the middle of the spring, tying off to a solid point at the rear and front of the horizontal door track. Extension springs represent a hazard to bystanders when a spring, pulley, or cable breaks under tension. Metal parts from extension spring systems can suddenly be launched.
If you are replacing an old garage door, the first step is to measure your garage opening to ensure you are choosing a door with the correct dimensions. Even if you feel confident that your door is a standard size, measuring first can help ensure that buying your door is an enjoyable and smooth process. View our installation guide to get the needed measurements for your door. If you find that you have an odd-sized garage door, use our QuickDraw tool to see how a specific model will look in your desired size. If you have a unique vision for your home's curb appeal, Clopay can also design custom garage doors to meet your specifications.
For Sears Garage Door Installation and Repair Services, making your garage door safe is as important as making it function well. For this reason, all of our repair services and tune-ups feature a 20-point safety check. Our technician will carefully examine your garage door panels, springs, sensors, safety release, hardware, track, and more. This ensures that, not only has our work been done well, but that your garage door poses no danger to your vehicles or family. Due to the intricacy of garage door systems, only garage service professionals should attempt to adjust, repair, or service door equipment.
If you have a steel door, but want the look of a wood one, it is not necessary to change your entire garage door. Often, it may be possible to mimic the look of wood with skillful painting. Your local home improvement store may be able to provide good advice about the type of paint and brushes needed to mimic the look of wood for your particular door material.
R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.
Our branch in the city of Tucson services the garage door needs of Old Pueblo including Oro Valleyand Marana in the northwest, Sahuarita and South Tucson in the south, and; the communities of Casas Adobes, Catalina Foothills, Flowing Wells, Midvale Park, Tanque Verde, Tortolita and Vail. We also cater to surrounding areas such as Catalina and Oracle in the north, Green Valley in the south and Benson on the southeast. When you call us, expect our technicians to arrive promptly and efficiently attend to your garage door needs.
It is precisely on those coldest days of the year when you most need and appreciate the convenience of opening and closing your garage door quickly. Sadly, those also happen to be the kinds of days when cold and moisture combine to make this difficult. Garage doors can and do freeze to the garage floor. Sometimes it is a minor icy connection between the two that can be broken when you hit the opener button.
Safe automatic door openers. All automatic openers must now have an auto-reversing mechanism and photoelectric eyes located near the floor on both sides of the door (see photo). If the door is closing and the beam between the eyes is interrupted, the door will automatically reverse. If the eyes aren’t connected, the door won’t operate. For instructions on how to install a new garage door opener, see How to Install a Garage Door Opener.

Garage door sensors 1 are safety devices that prevent the garage door from closing on people, cars, pets, or anything that may get in its way. Garage door sensors 1 are located at the side of the door opening and produce a beam of infrared light. If the beam that runs from one side to the other is interrupted, the door will automatically reverse before hitting the object. Garage door sensors 1 can be purchased separately and average in price from $50-$100.
"Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. "
Align the upper roller tracks by carefully lifting the door halfway. Lock it in place with two locking pliers, and install the supporting brackets on the back of the rails using 1-1/4 in. perforated angle iron (available at home centers and hardware stores). Install 1-1/2 x 1/4 in. stop bolts, with the threads to the inside of the track, at the end of each upper track.
For those of you interested in getting a new garage door, we can accommodate any style or size. Our garage door experts in the office and in the field can walk you through the entire process. Garage doors come in many different sizes. In most cases we can have a technician out the same day you call us to get an accurate measurement of your garage door. We work with customers every day on getting new custom doors, wood doors, steel doors or even glass doors! There are so many options to choose from and we try to educate you on all of those options so that you can make the buying decision that is right for you. We know that new garage doors are a big investment so it’s really important to have the right knowledge.
Precision has always gone out of their way to make our garage door work properly. We did have some issues with our warranty, but precision did work hard with us to come to a fair compromise. Our technician, Justin, was fair and honest and and did a good job for us. We appreciate the time he took to make things right! We always recommend Precision to our friends and family and will continue to do so. Thank you, Precision Doors!
@Neil What is the use of repeating lessons when there is so much more to be learned? Technology has moved on from the adz. Plumbers use PEC, insulation is sprayed, glue-lams allow for open floor plans and furnaces are no longer stoked with coal. As for the new people, if these trades cannot attract fresh blood we will all be unable to get homes built and repairs made. I don't yearn for my first home with the leaky concrete block foundation, failing well pump and an oil furnace held up by the plenum. I'll take heat pumps, solar panels and PVC waste pipes any day.You can get all the sill plate repairs and flitch beams demos you need on YouTube.
Been a long time listener to WLAC and felt any advertisers they would present were reliable. Precision came quickly to determine what was need to fix my garage door for my car and a commercial size for my travel trailer. The technician was very knowledgeable and knew exactly what was needed to fix my doors. I recommend Precision for any garage door repair.
If you can’t find one for your garage door opener model, you can try a universal remote or you can install a new receiver. A receiver replaces the radio frequency the opener uses with its own. An added bonus of a new receiver is that it will automatically update older openers to the new rolling code technology, which stops the bad guys from stealing your code. Just plug the new receiver into an outlet close to the opener, and run the two wires provided to the same terminals the wall switch is connected to.

Your garage door is used often, generally more than any other door on your home. Therefore, it’s important to make sure that it’s tough, dependable and weather resistant. Our doors are fully capable of meeting all these requirements and are specifically designed with our customers in mind. While durability is important, so is appearance and we offer many different styles and colors of garage doors to match your home or business.
Go for the look of wood with less upkeep with low-maintenance faux wood composite & steel garage doors from our Canyon Ridge® & Coachman® Collections. Our Gallery, and Classic Collection garage doors are also available with Ultra-Grain®, a wood look durable paint. If you’re looking for a more traditional look, our Classic™ Collection of steel raised panel and flush panel garage doors complement most home styles. Add one of our many decorative window options to customize the door's appearance and let natural light into your garage.
Install the vertical roller tracks first by wrapping the curved lip around the rollers. The top of these tracks should be approximately 8 in. below the top of the top section. Wait to install the upper tracks until this step is complete. Check the level of the top section to make sure the tops of the vertical roller tracks are level with each other. The bottom of the roller tracks should be at least 1/8 in. off the concrete floor. After leveling and mounting these tracks, install the upper roller (horizontal) tracks.
If the door goes up but goes down only when you hold down the wall switch, check to see that the safety sensors are in alignment. The small light on each sensor should be lit up when nothing is between them. Door sensors do go bad, so if no light is showing at all, you may need to replace them. You can save yourself some time by using the existing wires. Also, direct sunlight shining on sensor eyes can make them misbehave.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
The last thing you want to do now is to spend hundreds of dollars on garage door repair and end up hiring someone who can’t give you the quality service you need. When it comes to home garage doors, it is extremely important that you get the right value for every single dollar you pay. Not only do we offer low prices for repairs, but we also feature daily specials to save you even more money. We also have lifetime warranties available – another way we can strive to meet your needs.
"Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. Mile High garage called shortly after submitting my request and set an appointment to have a repair man show up shortly after. They went over everything I needed to get done and gave me several pricing options to fix initial need and alleviate future issues. Work was done in a timely manner and customer service was great. "
We also offer garage door opener repair service. Many times, what appears to be a problem with your garage door is actually a problem with your garage door opener. Our professional technicians have experience with all major garage door opener brands, including the popular LiftMaster line of garage door openers. Whether your garage door opener is making too much noise, failing to turn on, moving too slowly or not opening or closing your door properly, we can fix it fast.
Clopay Garage doors featuring Intellicore insulation technology represent Clopay Garage doors featuring Intellicore insulation technology represent the ultimate smart choice for homeowners. Clopay Intellicore is proprietary polyurethane foam that is injected into a garage door expanding to fill the entire structure. The result is a door with incredible strength and durability. Its dense insulation also produces a quieter ...  More + Product Details Close

Through our garage door configurator by Clopay, you can design, visualize and purchase a new Clopay garage door. Upload a photo of your home and then browse the configurator to see which style works for you. Choose from a variety of designs, textures, colors, finishes, window options and decorative hardware. You’re able to easily and quickly see the transformation, and then make it a reality.
With over 300 independently moving parts, your garage door is a deceptively complex piece of equipment. To help prevent malfunctions and break-downs, it is a good idea to occasionally perform a garage door tune-up to keep all of these parts in good working order. A regular tune-up service by a Sears professional can prevent unexpected door problems and prolong the life of your existing equipment.

Our garage door installation and repair professionals are courteous, knowledgeable, skilled and dedicated to your satisfaction. Let us show you what we’ve done for so many businesses and homes throughout Cincinnati and northern Kentucky when it comes to their garage doors, and what we can do for you. Once you’ve tried our services, you won’t have to search for a garage door service provider in this area ever again.


The nucleus of any garage door system is its opener. Easily overlooked, garage door openers are highly complex pieces of equipment, often containing dozens of intricate parts that work simultaneously with one another to consistently raise and lower your door. You'll know that you're getting the best from Sears as it's the home to America's #1 Garage Door Opener Brand, Craftsman*.


Incredible service. I heard the garage door spring break and knew it needed to be fixed. As it was Saturday at 12:15 I figured I would find someone to fix it next week. Did a Google search, found Precision and made a call. They sent Aaron right away (no extra charge for weekend or immediate service) He changed my broken spring as well as the spring on the other door, at my request, and was finished by 1:30. Aaron was very professional and did a great job, I'm a very happy customer.
Because your garage door is a major entryway to your home, it is important to keep it in good working order for your own safety, security, and convenience. Choosing the right style and appropriate materials will lessen the amount of repairs that may arise. Additionally, investing in regular maintenance can be cost-effective in the long run. If your garage door is in need of major repair, it is best to call a professional garage door repair company for assistance. Typically, the company will charge for at least one hour for making a service call. However, the benefits of a professional repair job can well outweigh any costs, as a professional can ensure the safety, security, and proper operation of your garage door.
Incredible service. I heard the garage door spring break and knew it needed to be fixed. As it was Saturday at 12:15 I figured I would find someone to fix it next week. Did a Google search, found Precision and made a call. They sent Aaron right away (no extra charge for weekend or immediate service) He changed my broken spring as well as the spring on the other door, at my request, and was finished by 1:30. Aaron was very professional and did a great job, I'm a very happy customer.
Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.
Carriage: These doors mimic the look of doors found on old carriage houses in the days of horses and buggies. Because of their rustic look, they are often favored in the West and Southwest of the United States. The doors swing open like oversized French doors and hang from jambs on hinges. With their unique look, they create an area of visual interest for your home and are quite energy efficient. The downside is they require a considerable amount of clearance to work properly. Because most carriage garage doors are largely composed of wood, you may need to replace deteriorating or rotting door materials. The average cost for carriage garage door repairs is $133.
Similar to other products, there is always the possibility of requiring maintenance for your garage door opener. Any unusual movements or sounds should be addressed immediately and brought to the attention of a repairman. Eventually with time, the motor is likely to fail. Other parts, including the springs, chains, hinges 4, etc., can start to fail sooner. Replacing these parts when they start to fail will help to extend the lifespan of the product. Lubrication is a good practice to keep the chains, rollers, hinges 4, and pulleys from failing and creating expensive repair bills.
When you’ve measured your door and found a replacement that you love, garage door installation and repair services are only a click or call away. Our vast network of independent Clopay Dealers provide dependable service, and are happy to help with regular maintenance and replacement parts after your door is installed. Replacement garage doors installed by our Master Authorized and Authorized dealers are also eligible for a 1-year installation warranty to ensure your door operates reliably. For a quote or to request local service, visit our convenient dealer locator to find a Clopay Dealer near you!
×