Replacing a circuit board sounds like a scary garage door repair, but it’s really quite easy. It will take 10 minutes tops and only requires a 1/4-in. nut driver. Just follow these steps: Remove the light cover, take out the lightbulb, disconnect the switch and safety sensor wires, remove a few screws, unplug the board and you’re done. A circuit board will cost about $80, so make sure you protect your new one with a surge protector. You can buy an individual outlet surge protector at a home center for less than $10.
If the outlet has power, but there’s no sound or no lights when you push the wall switch and remotes, you probably have a bad circuit board. Lightning strikes are the most frequent reason for the demise of a circuit board. The circuit board consists of the entire plastic housing that holds the lightbulb and wire terminals. The part number should be on the board itself.
Sears offers two different drive mechanisms to accommodate your home and budget. If you're looking for a smooth and quiet opener for a garage door with rooms located above the garage or attached to the garage, the belt drive is going to be the best for you. You can also choose a chain drive opener, which is perfect for garages that are unattached to the home.
Though we’ve grown a great deal, we still approach each customer with a focus on personalized service. We want to meet your needs as effectively as possible. We also provide a sense of urgency to each job, knowing that garage door needs often represent a significant life or work slowdown. Get in touch with us to schedule a visit, ask questions or to learn more about what we offer and how we can help get your garage door back up and running again.
They sent Doug Fussell out to my house on the day after Christmas! I had only called them three days before! Doug was a premier technician, very thorough and very efficient. I expected him to take two days, since he was replacing two doors and adding openers on each door. He only took the daylight hours of one day! I could not believe how fast he was! In addition, he thoroughly taught me how to use the remote openers. I highly recommend them to anyone!
It has the potential to be a good segment, but assuming all of the 'nightmares' might not be super obvious, I think instead of just laughing at pictures and making snarky comments, it would be helpful if they pointed out what exactly is wrong, why it's wrong, and what would be involved in remediating such a problem.With a home inspection as part of a real estate transactions, buyers are often faced with a decision of what to do with the information from the inspection- ex. do we walk away, asked for it to be fixed, just accept it, etc. So having the guys give that sort of context to the pictures would be helpful as well For example in the second photo with the little step, that might be really simple and cheap to fix, or maybe it requires a whole new porch be poured. Explaining that would make this so much better vs just snarking at the photo

When you pull up to your garage door and push the button for the opener, there’s one thing that should happen: your garage door should open smoothly, steadily, and quietly. However, if that’s not happening, contact the friendly professionals at Garage Door Service. We’re located in Loveland, Colorado, but we’re also prepared to offer service, garage door repair, and garage door opener repair to customers in Fort Collins, Windsor, and all over Northern Colorado, as well as Wyoming, Nebraska, and Kansas. No matter the problem, our technicians always come prepared with a wide range of parts and tools, so that we can repair your garage door during a single visit. We’re committed to providing reasonable rates, free estimates, and top-notch customer service. Our goal is to leave you with a working garage door and a smile.


The history of the garage door could date back to 450 BC when chariots were stored in gatehouses, but in the U.S. it arose around the start of the 20th century. As early as 1902, American manufacturers—including Cornell Iron Works—published catalogs featuring a "float over door." Evidence of an upward-lifting garage door can be found in a catalog in 1906.[4]
Measure the various areas where the door will be installed: door-opening height and width, headroom (from top of opening to ceiling), and back room (length of garage). For the headroom, you should have about 10" to 12" of space, depending on the spring system you're installing. For the back room, you should have the door height, plus another 18" or more of space.
A1 Garage Door Service is the trusted service provider in installing, servicing and repairing all kinds and types of garage doors. We encourage you to check out the reviews of the people of Phoenix, Tucson and southern Arizona on the kind of garage door service that we provide. Our customers have consistently given us A+ ratings on BBB, 5-star ratings on Yelp and the Super Service Award on Angie’s List to express their satisfaction on our service.
If the outlet has power, but there’s no sound or no lights when you push the wall switch and remotes, you probably have a bad circuit board. Lightning strikes are the most frequent reason for the demise of a circuit board. The circuit board consists of the entire plastic housing that holds the lightbulb and wire terminals. The part number should be on the board itself.
Looking to repair your garage door opener? Common problems could range from issues with the remote or wall switch that control the garage door opener to more serious issues like a grinding noise coming from the opener itself. If you need help with repairing your garage opener, schedule a repair appointment today! We repair all major brands and have same-day availability in most markets, so we can get your garage door opener repaired and running smoothly. To learn more about the cost of repairing garage doors, visit our garage door and opener installation and repair cost guide. Garage Door Repair Centennial Colorado
×